Are you of legal smoking age?

You must be of legal smoking age in your jurisdiction to shop with EightVape.

Sold Out

Tesla Biturbo Mech Dual RDA Kit

$ 0.00

SKU:

This product is sold out

Tesla Biturbo Dual Mech & RDA Kit

FOR ADVANCED USER ONLY!!! 

Tesla Biturbo Mech Dual RDA Starter Kit is a powerful device that has the ability to fire two RDAs at the same time for greater vapor productions. Users can add two flavors e-liquid into RDAs and enjoy a complex and unique taste. The device is equipped with buttons for channel selection at the bottom, which allows users to know the usage of this device better. All of these are designed to provide you with an unbeatable taste and quality. Innovation leads to changing life

Tesla Biturbo Mech Dual RDA Starter Kit Features & Spec:

  • 1 or 2 RDAs Arbitrary Switch
  • Channel Selection Button
  • Dual 18650 Cells Setup
  • Connector Bridge For RDAs
  • Great Vapor Productions
  • Wide Bore Drip Tip
  • Airflow Control System
  • Enjoy Two Flavors Simultaneously

Biturbo Mech Mod Features and Specifications:

  • Dimension:
    • 52 x 26 x 107mm(starter kit)
    • 52 x 26 x 88mm (Mod)
  • Material:Zinc Alloy(Die Cast)
  • Dual High Drain 18650 battery cells, rated 30A or better (NOT INCLUDED)
  • Thread Type: 510 thread
  • Min resistance:
    • 0.1Ohm (Single RDA) 
    • 0.2Ohm (Dual RDAs)
  • Input Voltage Range: 6.0V~8.4V
  • Standby Current: < 5uA
  • LED Indicator: Blue
  • Protections: Over puffing protection/ Reverse connection protection/ Atomizer short-circuit protection/ Low voltage alert.

Biturbo Mech RDA Specifications:

  • Diameter: 25mm
  • Height: 30mm
  • Adjustable Aiflow: Yes

Tesla Biturbo Mech Mod Operations
1. Power On: Insert two 18650 high-drain batteries i nto the body of the device. The blue LED A and B will falsh 5 times to indicate the dual channels are started, and device will enter the mode of stand-by.(We recommend using high-drain 18650 batteries with rated discharge current>30A. Please be careful about the positive and negative signs inside the battery compartments.)
2. Power Off: Press the fire button for 5 times consecutively when the device is powerd on, and corresponding LED will flash for 3 times to indicate that the device is powered off.
3. Vaping: Press the fire button simultaneously as you vape and release the fire button when vaping is not required.
4. Working Mode Switch: Users can enjoy the switching among four working modes: opened channel A adn B / Opened Channel A / Opened Channel B / Closed channel A adn B. Press channel selection button A/B to open or close the channel A/B.
5. Charging: Remove the 18650 batteries from the device and recharge the batteries buy using an proper recharging device.

 

Tesla Biturbo Mech RDA Operations
1. Steps for Installation: Before starting, make sure your hands are clean. Take RDA apart, install the pre-wrapped wire, and position and cut the ends of the wire off. Insert the cotton, and place it in the middle. Cut the cotton at an angle and make sure it's not too short or too long. Wet the coil with e-liquid and adjust the cotton.
2. Adjusting the Airflow: Adjust airflow through rotating the stainless tube, where a total of two airflow holes are located.

 

Tesla Biturbo Mech Starter Kit Protections
1. Over Puffing Protection: The device will deactivate after continuous puffing of more than 10 seconds. Then corresponding LED will flash for 8 times, and the device will enter the stand-by mode. 
2. Reverse Connection Protection: If batteries are inserted incorrectly, the device will fail to power on and will prevent any damage to the chipset.
3. Low Voltage Alert: When the voltage drops below 7.5V, corresponding LED will flash for 15 times and the device will power off.
4. Atomizer Short-circuit ProtectionWhen an atomizer short circuit occurs, corresponding LED will flash for 5 times rapidly and the device will enter the stand-by mode.

IMPORTANT NOTE & DISCLAIMER:

This device is strictly for ADVANCED USERS and it is NOT recommended for beginners or those who do not fully understand your battery's Amp Limits in correlation with your Atomizer's Resistance.  Use a married pair of new/genuine high drain batteries with this device.  Please be aware of what voltage your batteries are firing at and keep in mind the amp limitations of your batteries as well.  Use with extreme caution and always check your resistance with a meter (check often)!  By purchasing the product, you agree that you are knowledgeable on how to properly use this product and that we are NOT responsible for any misuse or accidental malfunctions of this product.

 

You might also like

Use special caution when working with Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable cells, as they are very sensitive to charging characteristics and may explode or burn if mishandled. Make sure the user has enough knowledge of Li-Ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable cells in charging, discharging, assembly and storage before use. Always charge in/on a fire-proof surface. Never leave charging batteries unattended. Do not use any rechargeable battery as well as any battery charger if any visible damage is present, as well as if the cell or charger has been stressed through mishandling, accidental or otherwise, even if damage may not be visible. Always store and transport rechargeable cells in a safe, non-conductive container in a controlled environment. Dispose of all battery cells and chargers in accordance to local laws and mandates.

Eightvape® USA will not be held responsible or liable for any injury, damage, or defect, permanent or temporary that may be caused by the improper use of a Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable battery/batteries. Please have a basic understanding of the batteries you are using and how to care for them properly.

All pictures are based on practicality, copyright reserved.